Designing a basic sock...Part 2

Welcome to the second part of designing a basic knitted sock! I hope that you are feeling a bit less daunted by the prospect , and are going to have a go at knitting your first sock :) . I am also going to answer a question about the beginning round of Magic Loop knitting. So here goes...

In the last post, you had measured your foot circumference and worked out your stitch gauge. You are now going to work out how many stitches you will need to knit your basic "tube", in order for it to fit comfortably.
Using your calculator (or if you happen to be a math genius...work it out in your head ;) ), subtract 10% of the circumference measurement of the ball of your foot, from the total measurement. So in my example, my foot circumference was 9 and 3/4 inches. 10% is equal to 0.975in, so my math will look as follows:


Since I have 6 and a half stitches in an inch for my gauge, I need to multiply 6.5 stitches, by 8.775in (the needed inch circumference of my foot). This gives me 57.04 stitches, which of course
is not possible, so I have to round this number to 57 stitches.

However, you want to have an even number of stitches , so that you can do a Judy's cast-on, so you have a choice...either round UP to 58 stsitches, or DOWN to 56 stitches. I am going to (arbitrarily), round down to 56 stitches for these sock posts.Right....you have determined how many stitches you need for the sock, but obviously you need to START your sock with fewer stitches...to make the toe. So, how many stitches are you going to cast on? A very general rule is to use ONE QUARTER the total number of stitches required for the sock, as the cast on number of stitches to make the toe.
So, if you need 56 sts in total for your sock, one quarter is 14 sts. Remember that you are going to use Judy's Magic cast-on, and this means that your 14 stitches are evenly cast on over the two needles....therefore you will end up with 7 stitches on each needle.

So lets recap...

Total number of stitches needed to knit the sock = 56sts
Number of stitches needed for the toe cast-on = 14 sts
(you will have half on one needle, and half on the other)
For this KAL, I am using a DK weight yarn, so I have relatively fewer stitches per inch than say someone who is knitting with proper sock yarn (will probably have somewhere between 8 and 10 stitches per inch for gauge). Remember, the formula....don't be concerned if your gauge doesn't match mine. Follow the steps above, and even if your results are different...your sock will still be right for you!

Tomorrow, we'll cast on and do the toe increases...so whip out your measuring tape and start your calculations :)

Magic Loop Revisited...

I wanted to do a quick recap of the first round of the Magic Loop knitting. You will use Judy's Magic Cast-On as the basis for the first round.



When you have cast on the required number of stitches, your needles will still be pointing to the left hand side. Remember to bring your tail yarn towards you and to the right across the working yarn.

Keeping your tail yarn in this position, rotate your needles clockwise to your right.


The pic above is what your work should look like...Now if you look closely, the side of the cast on facing you is actually the knit side....no purly bumps seen...


If you twist your needles over you'll see the purly side with little bumps...remember that the purl side will eventually be on the "inside" of your work as you knit in the round, and all the lovely knit stitches will be facing you (because you are just making "knit"stitches all the time...)


Remember that the needle that the working yarn (the yarn that comes from the ball of yarn) is coming from, is the needle that will be pulled to your right , being the one you use to start your knitting with. Once you have knitted several rounds, a little "pocket" will start to form, with all the purl stitches facing in and all the knit stitches facing out. But...at the beginning of your first round, you haven't yet gotten "sides"of knitted fabric to form the little pocket, so all you have, to guide you as to where you will insert your right hand needle, is the look of the cast on stitches, ie the "knit"vs "purl" sides, as seen above...

In order to insert your right side needle into the "knit" side of your first stitch, you will need to slightly twist your work , so that you are looking square onto the "knit " side of your cast on.


Things should look like the pic above...


Here, in the pic above, I have now knitted two stitches, and you can see that the "knit" side of the cast on is still facing me.

Once you have done enough rounds to form the pocket of knitting , it will be obvious where you need to knit into...but in the first few rounds it may be a little confusing, so just walk through the pics above step by step...if you start seeing purl and knit stitches on the SAME side of the fabric, you have gone wrong somewhere...

I hope that makes things a little clearer...

Have a good evening folks!
Lots of Love,
Heidi :)